See What Kia Picanto Key Fob Replacement Tricks The Celebs Are Using

How to Replace a Kia Sportage Replacement Key

The key in many Kia Picanto Key Fob Replacement models has an electronic keyless entry system built into. The key is usually akin to an electronic remote and can be changed by a new one purchased from a Kia dealer or a locksmith.

Key fobs can stop working due to a variety of reasons, such as a dead battery, worn-out buttons signal interference, or water damage. Here are some helpful tips on how to get your Kia Sportage replacement key to function again.

How do you replace a smartkey or remote key?

The battery in your Kia's intelligent key will eventually require to be replaced, whether it is a remote key, a push-to-start key or a standard metal key that does not contain an electronic transponder. This is particularly when your car shows a message that states the smart or remote keys are in poor condition.

It's a relatively simple process. In order to replace the battery on the key fob take out the mechanical key from the slit in the back of the key fob and break the cover. A small screw is found inside the key fob to keep the battery in the correct position. Remove the old battery by unscrewing the screw with a small screwdriver. Insert the new battery and close the opening on the key fob.

Once the key fob has an updated battery Test it by pressing the locks and unlock buttons. It's okay when the doors lock or unlock as expected. You can now use the hands-free lock/unlock feature on your Kia when your fingers are cold or you have to do some errands in Brandon.

Note: Certain key fobs may need to be programmed (transponder chips or smart keys). This requires a specific programming a kia key fob machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) do not require programming. If you want to change the programming of your key, you'll need to note the key code number on the key code tag.

How do you replace a battery?

If the 2015 kia soul key fob key fob is unable to respond to pressing the lock/unlock button, it is most likely that the battery is low. A low battery could cause other issues such as the check engine light flashing on or delayed engine cranking. Fortunately, replacing the key fob battery is a simple DIY project that requires only a few basic tools.

Make sure to shut off your vehicle and close the doors before you begin. Find the small metal or a plastic piece that is located at the bottom of the key fob. Press it until the metal key pops out. This key can be put into the door's driver handle to unlock your car.

To replace the battery in the key fob, take off the cover on the rear. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Remove the old battery and then position the new battery to ensure that its "+" side is facing you, and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid bending or damaging the contacts of the metal.

Once the new battery has been installed and the key fob is turned on, turn it off and then turn it on in the ignition repeatedly until the door locks. You can then test your kia picanto key fob key fob to check if it is working properly again.

How do I replace a smart key

There is a possibility of having a standard keyfob, or a Smart Key based upon the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade, while the standard key fob does not. Both key fobs have a battery that will eventually require replacing. Luckily, this is a fairly simple process that takes only two minutes.

Be sure to switch off your Kia and stand on a flat or well-lit surface prior to when you begin. Be aware that there are tiny components inside the fob that could fall out if not careful.

The first step is to locate the small release button on the lower backside of the fob. This will be either a circular button or a rectangular slot. You can open the key fob by pressing the button.

Once the key fob is opened, remove the old battery. The new battery should be a CR-2032 and can be bought online or from your local auto parts store. After you're done, your key fob should be able to lock the vehicle, unlock it, and then start your vehicle even if it's not running.

How to replace the mechanical key

The Kia key fob is a wonderful convenience that allows us to lock and unlock our vehicle with the push of a button. Like any device it is possible that the 2013 kia rio key replacement key fob might have issues. There are solutions to solve these issues and keep your key fobs running for a long time.

One of the most frequent problems is a low or dead battery. The battery could cause the device to stop working or operate intermittently. If this happens then try replacing the battery with a new one.

If this doesn't fix the issue Try using a standard flathead screwdriver and wedge it into the casing of the fob's plastic. Be careful not damage any internal components, or scratch the plastic. When the battery is open, carefully take off the battery you have been using and replace it with a new kia key fob one.

When the new battery is installed, close and unlock the doors with the mechanical key (every Kia fob comes with an emergency mechanical key that can fit into the slot). Test the fob to make sure it's working properly. If the device not working, contact an authorized locksmith or dealer to resolve the problem. Make sure they make you an emergency key that can work for all door and trunk cylinders to avoid lockouts in the future.